THE CORE OF THE ELECTRIC FLEET

Modular Battery Power Supply

Industrial battery power for your existing AC tools: 5.5 kW rated, with 15 kW peak to start motors and welders. Connect battery cutting and compaction with onsite breaking, repair and cleanup.

  • Low-frequency inverter
  • No engine exhaust
  • Shared batteries
  • Quick-release modules
Match power to my tools
Modular Battery Power Supply
5.5 kWRated AC output
15 kWPeak · motor & welder starting
7.7 kWhStored in 4 removable packs
200 ADC welder application

COMPLETE MOBILE POWER SYSTEM

$11,800USD

1 Station + 4 Packs + 1 Dock. AC power and mains charging included.

Configure this power system2-year retail warranty · Direct replacement for quality defects →U.S. suggested retail. Taxes and shipping excluded.

INDUSTRIAL-GRADE POWER

Built for starting loads.
Not just running ones.

Motors, compressors and welders draw several times their running power at start-up. The Dock is designed around that moment.

15 kW peak

Short-duration peak output to start motors, compressors, pumps and welders. Running loads stay within the 5.5 kW rated output.

Low-frequency transformer inverter

An industrial, transformer-based inverter design for inductive tool loads and repeated starting on site.

7.7 kWh in four removable packs

Each 64 V 30 Ah pack stores approx. 1.92 kWh. Take packs out to run the floor saw, rammer or plate compactor.

Starting performance depends on the exact model, its starting current and other connected loads.

BATTERY POWER FOR AC TOOLS

Power for breaking,
repair and cleanup.

Two breakers working together

Supports two compatible breakers operating together within the rated output.

200 A DC welder

Supplies AC input to a compatible welder for onsite repair work.

Pumps, washers & compressors

Powers compatible pumps, washers and compressors. Check the complete machine electrical input and starting requirements for the exact model.

These are individual supported applications, not a promise to run every listed tool together at full load. Match exact models, input power and starting loads to the power setup.

MODULAR BY DESIGN

Roll it together.
Move it in modules.

One battery cart, four packs and a power head. The full setup is approximately 130 kg; separate the quick-release modules for transport and reassemble on site.

STATION

Battery cart × 1

28 kg

The mobile base carries the batteries and assembled system.

PACKS

Each battery · 4 packs

18 kg

Remove packs individually; use them with compatible construction machines.

DOCK

Inverter power head × 1

28 kg

Provides AC output and manages charging and discharging of connected Stations.

Plan people and handling aids around component weights and the transport route.

CHARGING AROUND THE WORK

One Dock.
Two connected Stations.

One Dock supports two connected Stations for charging and discharging. Mains charging runs in sequence: one Station finishes, then the other starts.

0% → 80%

115 min

Approx. 115 minutes for four packs

0% → 100%

160 min

Approx. 160 minutes for four packs

Reference times use the matched mains-charging setup. They apply to one four-pack Station, not to both Stations charging simultaneously.

PERFORMANCE AT WORK

Know what the machine can do.

5.5 kWRated AC output
15 kWPeak · motor & welder starting
7.7 kWhStored in 4 removable packs
200 ADC welder application
Rated AC output
5.5 kW
Peak AC output
15 kW · motor and welder starting
Inverter type
Low-frequency (transformer-based), industrial grade
Full-output setup
At least 2 active packs meeting parallel-connection conditions
Single-pack rated AC output
2.5 kW (automatically reduced)
Standard configuration
1 Station + 4 Packs + 1 Dock
Expansion
One Dock accepts two Stations for charging and discharging
Complete system weight
Approx. 130 kg with four batteries
Station / Dock weight
28 kg each
Battery weight
18 kg per pack
Battery pack
64 V 30 Ah · approx. 1.92 kWh each
Stored energy, standard configuration
Approx. 7.7 kWh (4 packs)
Four-pack Station, 0–80%
Approx. 115 min
Four-pack Station, 0–100%
Approx. 160 min
Two-Station charging
Automatic sequential charging; one Station is completed before the next
Output versions
US / European configurations available
Protection features
Emergency stop, relays and multiple protective functions
System ingress protection (with batteries)
IP65

AC-tool compatibility depends on the exact model, input requirements, starting load and simultaneous use. Charging times are references under the matched mains-charging setup.

NEXT, START WITH YOUR JOB

Is this the right setup for your site?

Tell us about the tasks, workload and power available. Let’s check the configuration together.

Request a setup and quote